Products
Fabric duct shapes & suspension systems
Airvex fabric ducts are made to measure for each project, in 6 cross-section shapes to fit every space: from high-ceiling factories to low-ceiling offices, wall corners and spaces with special architecture.
Round fabric duct
The standard fabric duct shape: it distributes air evenly around the whole duct body and is easy to take down, refit and clean. It is the shape to choose first whenever space allows.
- Factories
- Warehouses
- Supermarkets
- Sports halls
- Farms
- Space height taken up
- Equal to diameter A
- Working pressure
- Positive pressure (supply air)
- Suitable suspension
- 1 or 2 suspension cables, or 1 or 2 aluminium rails (suspended or ceiling-mounted)
- Dimension parameters
- Diameter (A)
Half-round fabric duct
The flat side sits tight against the ceiling with the curved side facing down. Used when there is not enough room for a round duct, or when a compact, good-looking duct run is wanted.
- Offices
- Shops
- Showrooms
- Low ceilings
- Space height taken up
- About A/2
- Working pressure
- Positive pressure (supply air)
- Suitable suspension
- Half-round profile rail, fixed flush to the ceiling or suspended
- Dimension parameters
- Diameter (A)
Quarter-round fabric duct
Installed in the corner where the ceiling meets the wall, almost hidden in the structure. It saves space and helps reduce echo in the corner of the room.
- Offices
- Meeting rooms
- Corridors
- Classrooms
- Space height taken up
- Equal to radius A
- Working pressure
- Positive pressure (supply air)
- Suitable suspension
- Quarter-round profile rail, fixed into the ceiling–wall corner
- Dimension parameters
- Radius (A)
Segment fabric duct
An arc smaller than a half circle, fixed flush to the ceiling. Used when the remaining height is not enough for a half-round duct.
- Under beams
- Low service voids
- Refurbishment of existing buildings
- Space height taken up
- Equal to height B
- Working pressure
- Positive pressure (supply air)
- Suitable suspension
- Profile rail fixed flush to the ceiling
- Dimension parameters
- Width and height (A, B)
Sector fabric duct
A variant of the quarter-round shape for corners that are not square: sloping roofs, inclined beams or slanted walls.
- Sloping roofs
- Corners with beams
- Slanted walls
- Space height taken up
- Follows the structural angle
- Working pressure
- Positive pressure (supply air)
- Suitable suspension
- Profile rail made to match the actual corner angle of the building
- Dimension parameters
- Radius (A)
Square / rectangular fabric duct
A square-edged cross-section that suits architecture with many straight lines, or ceilings with beams and grids. It needs aluminium frames at the corners and threaded rods to keep the fabric taut and flat.
- Cleanrooms
- Showrooms
- Rectilinear spaces
- Space height taken up
- Equal to the vertical side B
- Working pressure
- Positive pressure (supply air)
- Suitable suspension
- Aluminium rail frame at all 4 corners, tensioned with threaded rods
- Dimension parameters
- Side lengths (A, B)
- 6cross-section shapes for every kind of space
- 100 – 2,000 mmmade-to-measure size range
- 20 / 50 Paminimum pressure for light / medium and heavy fabrics
- Supply airthese shapes work under positive pressure and discharge air into the space
Comparison
Choose the shape to suit the space
Choose a round duct whenever there is room. Switch to a ceiling-flush shape (half-round, segment) or a corner shape when height is limited, and choose square or rectangular when the architecture calls for clean, rectilinear forms.
| Shape | Dimensions | When to choose | Space height taken up | Typical projects |
|---|---|---|---|---|
| Roundcode C | Diameter (A) | Most common | Equal to diameter A | Factories, Warehouses, Supermarkets |
| Half-roundcode H | Diameter (A) | Low ceilings, clean look | About A/2 | Offices, Shops, Showrooms |
| Quarter-roundcode Q | Radius (A) | Wall-corner mounting | Equal to radius A | Offices, Meeting rooms, Corridors |
| Segmentcode SG | Width and height (A, B) | Very low ceilings | Equal to height B | Under beams, Low service voids, Refurbishment of existing buildings |
| Sectorcode SC | Radius (A) | Non-square corners | Follows the structural angle | Sloping roofs, Corners with beams, Slanted walls |
| Square / rectangularcode R | Side lengths (A, B) | Rectilinear architecture | Equal to the vertical side B | Cleanrooms, Showrooms, Rectilinear spaces |
Installation
Fabric duct suspension systems
The suspension is chosen according to the cross-section, the duct size and the ceiling structure. The larger the duct or the longer the run, the more rails or cables it needs.
Single cable
One steel cable runs along the duct line and the duct hooks onto it. Compact and low cost.
Double cable
Two parallel cables, one on each side, hold the duct more steadily. Suits large ducts.
Single aluminium rail
An aluminium rail, suspended or ceiling-mounted; the duct slides into the rail for a straight, neat line.
Double aluminium rail
Two parallel rails for large-diameter ducts or long runs.
Profile rail
Half-round, quarter-round or rectangular rail, fixed flush to the ceiling or into a wall corner.
Corner tension frame
A four-corner aluminium frame with threaded rods keeps square and rectangular ducts taut and flat.
Shapes and suspension by model
Each Airvex model is available in the shapes and suspension systems below. Open a model for its full specification.
- AV-T · Standard HVAC fabric ductShapesRoundHalf-roundQuarter-roundSuspensionSteel cable: single or parallel rows
Aluminium rail: surface-mounted or suspended
Steel pipe: single or parallel rows - AV-J · Cleanroom fabric ductShapesRoundHalf-roundSuspensionSteel cable: single or parallel rows
Aluminium rail: surface-mounted or suspended
Steel pipe: single or parallel rows - AV-F · Non-combustible fabric ductShapesRoundHalf-roundQuarter-roundSuspensionSteel cable: single or parallel rows
Aluminium rail: surface-mounted or suspended
Steel pipe: single or parallel rows - AV-RT · Framed fabric ductShapesRoundSuspensionSteel cable: single or parallel rows
Aluminium rail: surface-mounted or suspended
Steel pipe: single or parallel rows - AV-RF · Framed non-combustible fabric ductShapesRoundSuspensionSteel cable: single or parallel rows
Aluminium rail: surface-mounted or suspended
Steel pipe: single or parallel rows - AV-W · Insulated fabric ductShapesRoundHalf-roundSquare / rectangularSuspensionSteel cable: single or parallel rows
Steel pipe: single or parallel rows - AV-RW · Insulated return air fabric ductShapesRoundSquare / rectangularSuspensionSteel cable: single or parallel rows
Steel pipe: single or parallel rows
Real projects
Airvex fabric ducts on site



Not sure which shape fits?
Send us your floor plan and ceiling height. An Airvex engineer will recommend the shape, the suspension and the air outlets, together with a quotation.
Read the fabric duct FAQ
AV-T
AV-J
AV-F
AV-RT
AV-RF
AV-W
AV-RW
Cold stores & food
Supermarkets & malls
Cleanrooms & pharma
Sports halls & auditoriums
Livestock farms